1 Purpose and Functions
The ACTii AC3463 wireless switch is a high-quality single-channel radio relay designed for remote control of electrical devices powered by 230V. The device allows for convenient switching of receivers on and off using the included radio remote control, eliminating the need for complex wiring to traditional wall switches.
The system is widely used for controlling lighting (lamps), consumer electronics (TVs), electric motors, fans, and home automation systems such as electric door, lock, or window controls. Thanks to encoded transmission (433MHz frequency), each remote control is assigned to a specific switch, ensuring there is no interference when using multiple sets in one location.
Main features:
- ✔ Wireless single-channel switch
- ✔ Remote control via included radio remote
- ✔ High output power up to 1000W
- ✔ 230V AC mains power
- ✔ Solid construction from ABS and aluminium materials
- ✔ Practical wall mount for the remote included
- ✔ Encoded transmission preventing interference
- ✔ State memory after power failure
Principle of operation and pairing:
The device operates based on 433MHz radio transmission. Pressing the appropriate button on the remote sends a signal to the relay module, which closes or opens the circuit powering the connected device. The remote and switch are factory-paired, ensuring instant readiness for operation after taking them out of the box and connecting properly.
2 Technical Specifications
| Number of channels | 1 |
| Input power | 230V (200 - 245V) AC 50/60Hz |
| Maximum output load | 1x 1000W |
| Transmission range (indoors) | up to 20m |
| Transmission range (outdoors) | up to 100m |
| Operating frequency | 433 MHz |
| Remote power | 1x 23A 12V battery |
| Housing material | ABS, Aluminium |
| Switch dimensions | 51 x 37 x 21 mm |
| Remote dimensions | 105 x 45 x 16 mm |
| Product weight | 85 g |
| Certificates | CE, ROHS |
3 Installation and Connection Guide
Warning: Electric shock hazard!
Installation should be performed by a qualified electrician. Before starting work, it is essential to disconnect the power supply from the electrical network.
Wiring diagram:
The device has leads that must be connected according to the description below:
- Black: Neutral wire (N) - 230V power input for the switch.
- Black: Neutral wire (N) - output to the controlled device.
- Red: Phase wire (L) - 230V power input for the switch.
- Blue: Phase wire (L) - power output to the controlled device.
Installation sequence:
- Turn off the circuit breakers in the circuit where the switch will be installed.
- Check for the absence of power in the wires using a voltage tester.
- Connect the power wires (Red L, Black N) to the home installation.
- Connect the output wires (Blue L, Black N) to the receiver (e.g., lamp).
- Secure the connections with electrical blocks or appropriate insulation.
- Place the module in a box or the device casing.
- Turn on the power and test operation using the remote.
4 Operation and Usage
Remote control:
The remote has dedicated buttons for managing the relay state:
- Button ON/A: Turns the connected device on.
- Button OFF/B: Turns the connected device off.
Battery replacement:
If the remote range is significantly reduced or the LED on the remote stops glowing, the battery should be replaced. The remote is powered by one 23A 12V battery. To replace the battery, carefully open the remote casing, observing correct polarity (+/-) when inserting a new cell.
Wall mount:
Included with the set is a mount that can be screwed or glued to the wall, providing a permanent and convenient storage place for the remote.
5 Safety and Maintenance
- ●Do not exceed the maximum load of 1000W. Overloading may lead to permanent damage of the relay or fire.
- ●The device is designed for indoor use. Protect it from moisture, water, and extreme temperatures.
- ●In case of damage to the housing or cables, immediately disconnect the device from power.
- ●Do not open the relay module housing while it is connected to the 230V mains.
- ●Keep out of reach of children.
6 Set Contents
- 1x Wireless switch module (receiver)
- 1x Remote control (transmitter)
- 1x Wall mount for the remote
- User manual